Alurinmorin Lesa Amudani: Itọsọna Itọkasi pipe
Tabili Akoonu:
Alurinmorin Lesa Amudani:
Iwe Itọkasi:
Ibere:
Alurinmorin lesa amusowo nfunni ni ọpọlọpọ awọn anfani, ṣugbọn o tun niloakiyesi akiyesi si awọn ilana aabo.
Nkan yii yoo ṣawari awọn ero aabo bọtini fun alurinmorin laser amusowo.
Bi daradara bi pese awọn iṣeduroon shielding gaasi yiyan ati kikun waya àṣàyànfun wọpọ irin orisi.
Alurinmorin lesa amudani: Aabo dandan
Ohun elo Idaabobo Ti ara ẹni (PPE):
1. Lesa Aabo gilaasi ati Face Shield
Patakilesa ailewu gilaasi ati ki o kan oju shieldjẹ dandan labẹ awọn itọnisọna ailewu laserlati daabobo oju oniṣẹ ẹrọ ati oju lati ina ina lesa ti o lagbara.
2. Welding ibọwọ & Aso
Awọn ibọwọ alurinmorin gbọdọ jẹnigbagbogbo ayewo ati ki o rọpoti wọn ba tutu, ti rẹ, tabi ti bajẹ lati ṣetọju aabo to peye.
Imudaniloju ina ati jaketi-ooru, awọn sokoto, ati awọn bata orunkun ti n ṣiṣẹgbọdọ wa ni wọ ni gbogbo igba.
Awọn aṣọ wọnyi yẹ ki o jẹlẹsẹkẹsẹ paarọ wọn ti wọn ba tutu, ti wọ, tabi ti bajẹ.
3. Respirator pẹlu Ṣiṣẹ Air Filtration
Atẹmisi ti o ni imurasilẹpẹlu ti nṣiṣe lọwọ air asenilo lati daabobo oniṣẹ ẹrọ lọwọ eefin ipalara ati awọn patikulu.
Itọju to dara ati awọn sọwedowo igbagbogbo jẹ pataki lati rii daju pe eto naa n ṣiṣẹ ni deede.
Mimu Ayika Alurinmorin Ailewu:
1. Ti nso Area
Agbegbe alurinmorin gbọdọ jẹ mimọ ti eyikeyiawọn ohun elo flammable, awọn nkan ti o ni itara ooru, tabi awọn apoti ti a tẹ.
Pẹlu awọnnitosi nkan alurinmorin, ibon, eto, ati onišẹ.
2. Agbegbe Ti a ti sọ di mimọ
Alurinmorin yẹ ki o wa ni o waiye niagbegbe ti a yàn, ti a fipade pẹlu awọn idena ina to munadoko.
Lati yago fun ona abayo ti ina ina lesa ati dinku ipalara tabi ibajẹ ti o pọju.
Gbogbo eniyan ti nwọle agbegbe alurinmoringbọdọ wọ ipele aabo kanna bi oniṣẹ.
3. Pajawiri Tiipa
A pa yipada ti sopọ si ẹnu-ọna ti awọn alurinmorin agbegbe yẹ ki o wa fi sori ẹrọ.
Lati ku lẹsẹkẹsẹ eto alurinmorin laser ni ọran ti titẹsi airotẹlẹ.
Amusowo lesa Welding: Yiyan Abo
Ohun elo Idaabobo Ti ara ẹni (PPE):
1. Welding aṣọ
Ti aṣọ alurinmorin amọja ko si, aṣọ ti o jẹko ni rọọrun flammable ati ki o ni gun apa asole ṣee lo bi yiyan, pẹlu bata ti o yẹ.
2. Atẹgun
A respirator pepade ipele ti a beere fun aabo lodi si eruku ipalara ati awọn patikulu irinle ṣee lo bi yiyan.
Mimu Ayika Alurinmorin Ailewu:
1. Agbegbe ti a fi pa mọ pẹlu Awọn ami Ikilọ
Ti o ba ṣeto awọn idena laser jẹ aiṣe tabi ko si, agbegbe alurinmoringbọdọ wa ni samisi kedere pẹlu awọn ami ikilọ, ati gbogbo awọn ẹnu-ọna gbọdọ wa ni pipade.
Gbogbo eniyan ti nwọle agbegbe alurinmoringbọdọ ni ikẹkọ ailewu lesa ati ki o jẹ akiyesi iseda alaihan ti tan ina lesa.
Ni iṣaaju aabo jẹ pataki julọ ni alurinmorin laser amusowo.
Nipa titẹmọ awọn ilana aabo dandan ati murasilẹ lati gba awọn ọna yiyan igba diẹ nigbati o jẹ dandan.
Awọn oniṣẹ le rii daju a ailewu ati lodidi alurinmorin ayika.
Lesa alurinmorin ni ojo iwaju. Ati ojo iwaju Bẹrẹ pẹlu Rẹ!
Awọn iwe itọkasi
Alaye ti a pese ninu nkan yii jẹ ipinnu bia gbogboogbo Akopọti lesa alurinmorin sile ati ailewu riro.
Kọọkan kan pato alurinmorin ise agbese ati lesa alurinmorin etoyoo ni oto awọn ibeere ati ipo.
O ti wa ni strongly niyanju lati kan si alagbawo pẹlu rẹ lesa ẹrọ olupese fun alaye itọnisọna.
Pẹlu awọn iṣeduro, ati awọn iṣe ti o dara julọ ti o wulo si ohun elo alurinmorin pato rẹ ati ẹrọ.
Alaye gbogbogbo ti a gbekalẹ nibiko yẹ ki o gbẹkẹle nikan.
Bi specialized ĭrìrĭ ati itoni lati lesa eto olupese jẹ pataki fun ailewu ati ki o munadoko lesa alurinmorin mosi.
Alloy Aluminiomu Lesa Welding:
1. Ohun elo Sisanra - Alurinmorin Power / Iyara
| Sisanra (mm) | Iyara alurinmorin lesa 1000W | Iyara alurinmorin lesa 1500W | Iyara alurinmorin lesa 2000W | 3000W Lesa Welding Speed |
| 0.5 | 45-55mm/s | 60-65mm / s | 70-80mm / s | 80-90mm / s |
| 1 | 35-45mm/s | 40-50mm / s | 60-70mm / s | 70-80mm / s |
| 1.5 | 20-30mm/s | 30-40mm / s | 40-50mm / s | 60-70mm / s |
| 2 | 20-30mm/s | 30-40mm / s | 40-50mm / s | |
| 3 | 30-40mm / s |
2. Niyanju Shielding Gas
Argon (Ar) mimọjẹ gaasi idabobo ti o fẹ fun alurinmorin laser ti awọn ohun elo aluminiomu.
Argon n pese iduroṣinṣin arc ti o dara julọ ati aabo fun adagun weld didà lati ibajẹ oju-aye.
Eyi ti o ṣe pataki funmimu awọn iyege ati ipata resistanceti aluminiomu welds.
3. Niyanju Filler Waya
Aluminiomu Alloy Filler Wires ti wa ni lo lati baramu awọn tiwqn ti awọn mimọ irin ni welded.
ER4043- Aluminiomu okun waya ti o ni ohun alumọni ti o dara fun alurinmorin6-jara aluminiomu alloys.
ER5356- Magnẹsia ti o ni okun waya kikun aluminiomu ti o dara fun alurinmorin5-jara aluminiomu alloys.
ER4047- Aluminiomu kikun okun waya ohun alumọni ọlọrọ ti a lo fun alurinmorin4-jara aluminiomu alloys.
Awọn iwọn ila opin waya ojo melo awọn sakani lati0.8 mm (0.030 in) si 1.2 mm (0.045 in)fun amusowo lesa alurinmorin ti aluminiomu alloys.
O ṣe pataki lati ṣe akiyesi pe awọn ohun elo aluminiomu niloti o ga ipele ti cleanliness ati dada igbaradiakawe si miiran awọn irin.
Lesa Alurinmorin Erogba Irin:
1. Ohun elo Sisanra - Alurinmorin Power / Iyara
| Sisanra (mm) | Iyara alurinmorin lesa 1000W | Iyara alurinmorin lesa 1500W | Iyara alurinmorin lesa 2000W | 3000W Lesa Welding Speed |
| 0.5 | 70-80mm / s | 80-90mm / s | 90-100mm / s | 100-110mm / s |
| 1 | 50-60mm / s | 70-80mm / s | 80-90mm / s | 90-100mm / s |
| 1.5 | 30-40mm / s | 50-60mm / s | 60-70mm / s | 70-80mm / s |
| 2 | 20-30mm/s | 30-40mm / s | 40-50mm / s | 60-70mm / s |
| 3 | 20-30mm/s | 30-40mm / s | 50-60mm / s | |
| 4 | 15-20mm / s | 20-30mm/s | 40-50mm / s | |
| 5 | 30-40mm / s | |||
| 6 | 20-30mm/s |
2. Niyanju Shielding Gas
Apapo tiArgon (Ar)atiErogba Dioxide (CO2)ti wa ni commonly lo.
Awọn aṣoju gaasi tiwqn ni75-90% Argonati10-25% Erogba Dioxide.
Adalu gaasi yii ṣe iranlọwọ fun imuduro aaki, pese ilaluja weld ti o dara, ati aabo adagun weld didà lati ibajẹ oju-aye.
3. Niyanju Filler Waya
Irin Irin or Low-Alloy Irinkikun onirin wa ni ojo melo lo fun erogba, irin alurinmorin.
ER70S-6 - Idi gbogboogbo irin okun waya kekere ti o dara fun titobi pupọ ti awọn sisanra irin erogba.
ER80S-G- A ti o ga agbara kekere-alloy irin waya fun dara darí-ini.
ER90S-B3- A kekere-alloy irin waya pẹlu boron kun fun pọ si agbara ati toughness.
Iwọn ila opin waya ni a maa n yan da lori sisanra ti irin ipilẹ.
Ojo melo orisirisi lati0.8 mm (0.030 in) si 1.2 mm (0.045 in)fun amusowo lesa alurinmorin ti erogba, irin.
Idẹ Alurinmorin lesa:
1. Ohun elo Sisanra - Alurinmorin Power / Iyara
| Sisanra (mm) | Iyara alurinmorin lesa 1000W | Iyara alurinmorin lesa 1500W | Iyara alurinmorin lesa 2000W | 3000W Lesa Welding Speed |
| 0.5 | 55-65mm/s | 70-80mm / s | 80-90mm / s | 90-100mm / s |
| 1 | 40-55mm / s | 50-60mm / s | 60-70mm / s | 80-90mm / s |
| 1.5 | 20-30mm/s | 40-50mm / s | 50-60mm / s | 70-80mm / s |
| 2 | 20-30mm/s | 30-40mm / s | 60-70mm / s | |
| 3 | 20-30mm/s | 50-60mm / s | ||
| 4 | 30-40mm / s | |||
| 5 | 20-30mm/s |
2. Niyanju Shielding Gas
Argon mimọ (Ar)jẹ gaasi idabobo ti o dara julọ fun alurinmorin laser ti idẹ.
Argon ṣe iranlọwọ lati daabobo adagun weld didà lati ibajẹ oju-aye.
Eyi ti o le ja si nmu ifoyina ati porosity ni idẹ welds.
3. Niyanju Filler Waya
Awọn onirin kikun idẹ jẹ igbagbogbo lo fun idẹ alurinmorin.
ERCuZn-A tabi ERCuZn-C:Iwọnyi jẹ awọn okun onirin alloy alloy Ejò ti o baamu akojọpọ ohun elo idẹ mimọ.
ERcuAl-A2:Okun okun waya alloy alloy Ejò-aluminiomu ti o le ṣee lo fun idẹ alurinmorin bakanna bi awọn ohun elo ti o da lori bàbà miiran.
Awọn waya opin fun idẹ lesa alurinmorin jẹ maa n ni ibiti o ti0.8 mm (0.030 in) si 1.2 mm (0.045 in).
Irin Alagbara Alurinmorin lesa:
1. Ohun elo Sisanra - Alurinmorin Power / Iyara
| Sisanra (mm) | Iyara alurinmorin lesa 1000W | Iyara alurinmorin lesa 1500W | Iyara alurinmorin lesa 2000W | 3000W Lesa Welding Speed |
| 0.5 | 80-90mm / s | 90-100mm / s | 100-110mm / s | 110-120mm / s |
| 1 | 60-70mm / s | 80-90mm / s | 90-100mm / s | 100-110mm / s |
| 1.5 | 40-50mm / s | 60-70mm / s | 60-70mm / s | 90-100mm / s |
| 2 | 30-40mm / s | 40-50mm / s | 50-60mm / s | 80-90mm / s |
| 3 | 30-40mm / s | 40-50mm / s | 70-80mm / s | |
| 4 | 20-30mm/s | 30-40mm / s | 60-70mm / s | |
| 5 | 40-50mm / s | |||
| 6 | 30-40mm / s |
2. Niyanju Shielding Gas
Argon mimọ (Ar)jẹ gaasi idabobo ti a lo julọ fun alurinmorin laser alagbara, irin.
Argon pese iduroṣinṣin arc ti o dara julọ ati aabo fun adagun weld lati ibajẹ oju aye.
Ewo ni o ṣe pataki fun mimu awọn ohun-ini sooro ipata ti irin alagbara irin.
Ni awọn igba miiran,Nitrojiini (N)ti wa ni tun lo fun Lesa Alurinmorin alagbara, irin
3. Niyanju Filler Waya
Awọn onirin kikun irin alagbara, irin alagbara ni a lo lati ṣetọju resistance ipata ati awọn ohun-ini irin ti irin ipilẹ.
ER308L- Erogba kekere 18-8 okun waya irin alagbara fun awọn ohun elo idi gbogbogbo.
ER309L- A 23-12 alagbara, irin waya fun alurinmorin dissimilar awọn irin bi erogba, irin to alagbara, irin.
ER316L- Erogba kekere 16-8-2 okun waya irin alagbara pẹlu molybdenum ti a ṣafikun fun imudara ipata resistance.
Awọn waya opin ni ojo melo ni ibiti o ti0.8 mm (0.030 in) si 1.2 mm (0.045 in)fun amusowo lesa alurinmorin ti irin alagbara, irin.
Amudani Lesa Welder [Awotẹlẹ Iṣẹju 1]
Ẹyọ kan, ẹyọ amusowo ti o le yipada lainidi laarinalurinmorin lesa, lesa ninu, ati lesa gigeawọn iṣẹ-ṣiṣe.
Pẹlukan ti o rọrun yipada ti nozzle asomọ, awọn olumulo le seamlessly mu ẹrọ si wọn pato aini.
Boyadida irin irinše, yọ dada impurities, tabi gbọgán gige ohun elo.
Ohun elo irinṣẹ laser okeerẹ n pese agbara lati koju ọpọlọpọ awọn ohun elo.
Gbogbo lati irọrun ti ẹrọ ẹyọkan, rọrun-si-lilo.
Ti o ba gbadun fidio yii, kilode ti o ko ronuṣiṣe alabapin si ikanni Youtube wa?
Awọn iṣeduro ẹrọ fun Alurinmorin Lesa Amudani
Eyi ni diẹ ninu Imọ-imọ Laser ti o le nifẹ si:
Akoko ifiweranṣẹ: Oṣu Keje-12-2024